Overview & Specs

Vertec VT6600 Grain Dryer Review, Specs & Used Buyer’s Guide — Canada

The Vertec VT6600 is the portable continuous-flow member of the Vertec range — a screenless, Vermilion-built dryer most often found in 6-, 7-, and 9-tier configurations on the Canadian used market. Its defining trait is flexibility: the portable continuous design lets a farm move the dryer, site it seasonally, or run it where a fixed tower won’t fit. Listings commonly show it with a 4-to-6 million BTU burner running single-phase power, with capacity in the ~600 bu/h class depending on tier count and crop — a practical mid-range option for prairie operations that want continuous-flow drying without a permanent installation.

This guide is for the Canadian buyer weighing a used VT6600 and for owners after specs and honest guidance. Transparency note up front: unlike the PAMI-tested VT5600R, the VT6600’s figures here come from Canadian used-market listings and auction records, where configurations vary (6, 7, or 9 tiers; 4M or 6M BTU; PTO or electric). Treat the numbers as listing-derived and confirm the exact configuration of any specific machine with the seller.

Aglist quick take: The VT6600 is the flexible, portable Vertec — screenless continuous flow in a movable package, typically ~600 bu/h class and often single-phase, which makes it more yard-friendly than the three-phase VT8600. It suits farms that value siting flexibility and proven simplicity at used-market value. Where to be careful: configurations vary widely (tiers, burner, drive), so the spec on one VT6600 may differ from the next — verify the specific machine. Figures here are listing-derived, not PAMI-tested.

On This Page

Quick Verdict — Who the VT6600 Is For

Buy it if: you want a portable, screenless continuous-flow dryer you can site flexibly, your volume fits the ~600 bu/h class, and you prefer single-phase-friendly power and proven Vertec simplicity at used value. Good for mid-size prairie farms that don’t want a fixed tower installation.

Skip it if: you need the high throughput of the VT8600, you want factory automation without retrofitting, or you need a guaranteed fixed spec — the VT6600’s wide configuration variance means each used machine differs, so it’s less predictable than a single-config model.

1. Vertec VT6600 Specifications

The figures below are drawn from Canadian used-market listings and auction records. The VT6600 appears in multiple configurations, so these are representative ranges — confirm the exact specification of any specific machine with the seller.

Category	Spec	Value (listing-derived)
Type	Dryer design	Portable continuous, screenless
	Tiers	6, 7, or 9 (configuration-dependent)
Capacity	Quoted class	~600 bu/h (crop/config/removal-dependent)
Burner	Rating	~4–6 million BTU/h (config-dependent)
	Fuel	Natural gas or propane
Power	Typical	Often single-phase; PTO blower or electric
Manufacturer		Vertec Industries Ltd., Vermilion, Alberta
Design family		Vertec continuous multi-flow
Portability		Portable / transportable design
Market		Used only

Source: Canadian used-market listings (Kijiji, AgDealer, RB Auction, Farms.com) and auction records. Example listing references include a 9-tier VT6600 quoted around 600 bu/h on a 4M BTU burner, single-phase, PTO blower; and 6M BTU natural-gas single-phase configurations. Capacity depends on tiers, crop, and moisture removal — verify with the seller. For independently tested Vertec performance, see the VT5600R page.

2. Owner Reviews & Ratings on Aglist

The VT6600 has a solid prairie owner base, especially among farms that value portability. As Canadian owners share their experience on Aglist, the rating system tracks:

Reliability — burner and drive durability, harvest-season uptime
Capacity — real throughput on your crops and tier configuration
Fuel efficiency — gas / propane use in your conditions
Portability & setup — moving and siting the dryer
Serviceability — parts availability and retrofit experience

If you own or have run a VT6600 in Canada, please leave a star rating and a short note below — and mention your tier count and burner, since configurations vary so widely. That detail genuinely helps the next buyer compare like with like.

3. How the VT6600 Compares

The VT6600 is the portable mid-capacity option in the Vertec family. Here’s how it frames against its siblings and a modern portable alternative.

Spec	Vertec VT6600	Vertec VT5600R	Vertec VT8600	Super-B SQ20
Type	Portable continuous	Continuous multi-flow	Continuous flow	Portable continuous
Tiers	6–9 (config)	6	6	n/a
Capacity class	~600 bu/h	~334 bu/h wheat (5%, PAMI)	~1,800 bu/h	Modern portable
Power	Often single-phase	3-phase or 1-phase	600V 3-phase	Modern
Screenless	Yes	Yes	Yes	—
Portability	Portable	Transportable	Larger/heavier	Portable
Controls	Mechanical (retrofit avail.)	Mechanical (retrofit avail.)	Mechanical (retrofit avail.)	Modern
Test data	Listing-derived	PAMI 289	Listing-derived	—

Where the VT6600 wins: portability and siting flexibility, single-phase-friendly configurations, screenless low-maintenance design, and value pricing. A practical middle option between the mid-size VT5600R and the high-capacity VT8600.

Where it loses: configuration variance makes specs unpredictable machine-to-machine, capacity is listing-derived rather than PAMI-tested, and original controls are mechanical. For a modern portable continuous dryer with factory controls, compare the Super-B SQ-series. Full Vertec range and parts support is on the Vertec hub.

4. Real-World Performance

Capacity & Configuration

The VT6600’s ~600 bu/h class figure is genuinely configuration-dependent — a 9-tier machine behaves differently from a 6-tier, and crop and moisture removal shift throughput substantially. This is the model where “which exact machine” matters most: two VT6600s in different listings can have meaningfully different capacity. Use the PAMI-tested VT5600R as your reference point for how Vertec capacity scales with crop and removal, and confirm the specific tier count and burner on any VT6600 you’re considering.

Portability

This is the VT6600’s signature advantage over the larger Vertecs. The portable continuous design lets you move and site the dryer with more flexibility than a fixed installation — useful for farms with multiple sites, rented land, or yards where a permanent tower isn’t practical. Many run a PTO blower, which fits operations without heavy three-phase electrical infrastructure.

Burner & Power

Listings show 4M and 6M BTU configurations, often single-phase, sometimes PTO-driven. That single-phase friendliness is a real plus over the three-phase VT8600 for typical farm yards. Confirm fuel type (natural gas vs propane) and drive (PTO vs electric) against what your operation can supply.

Screenless Serviceability

Like every Vertec, the VT6600 is screenless — easy plenum and trough cleanout, no screens to blind with fines or canola. Combined with portability, it makes for a dryer that’s both flexible to site and straightforward to maintain.

5. Common Problems & Reliability Notes

Transparency note: these reflect the realities of a decades-old portable dryer with wide configuration variance. Inspect thoroughly and confirm the exact spec before buying.

Configuration variance. The single biggest VT6600 caveat: tiers (6/7/9), burner (4M/6M BTU), fuel, and drive all vary between machines. Don’t assume one VT6600’s spec applies to another — verify each individually.

Burner condition and age. As with all legacy Vertecs, burner condition drives value. A Maxon retrofit is a plus; an original tired burner is a future cost.

Original mechanical controls. Metering-roll adjustment is mechanical and sensitive on original machines. A moisture-controller retrofit improves usability.

Drive type considerations. PTO-blower machines tie up a tractor during drying; electric conversions exist. Match the drive to how you want to run the dryer.

Sheet-metal and plenum integrity. Check for corrosion, warped tiers, and plenum air leaks on a decades-old frame; higher garner sides (later improvement) reduce air escape.

Belt and drive wear. Inspect drive belts and the cross-auger belt (known Vertec wear point per PAMI’s VT5600R testing); keep spares.

6. Price Range in Canada (Used)

The VT6600 is sold exclusively used. Pricing varies with tier count, burner, drive, controls, and condition.

Project / original-condition units: typically CAD $12,000–$22,000
Good updated units: typically CAD $22,000–$35,000 — sound burner, good tiers, updated controls
Higher-tier / well-retrofitted examples: can exceed CAD $35,000

Price on condition and configuration, not just model name — a 9-tier updated machine and a 6-tier original are very different dryers at potentially similar headline prices. Confirm tier count and burner before comparing prices.

7. Best Use Cases in Canadian Conditions

Multi-site or flexible prairie operations (SK / AB / MB). The portable design suits farms that move the dryer between sites, rent land, or can’t commit to a fixed tower installation.

Single-phase yards. The VT6600’s common single-phase and PTO configurations fit farms without heavy three-phase electrical infrastructure — a practical edge over the three-phase VT8600.

Mid-volume cereal and canola farms. The ~600 bu/h class (higher-tier configs) suits operations whose daily intake fits that range. Screenless design handles dusty cereals and fine canola cleanly.

Buyers wanting Vertec simplicity with portability. For those who like the proven, serviceable Vertec platform but want flexibility to move the machine.

Not ideal for: high-volume operations needing the VT8600’s throughput, buyers wanting a guaranteed fixed spec (configurations vary too much), or those wanting factory automation out of the box.

8. Maintenance & Service

Standard Vertec continuous-flow service practice applies:

Lubrication: grease fittings and seasonal bearing oiling per the owner’s manual; check drive oil levels seasonally.
Cleaning: clear plenums and swing-down troughs regularly; remove accumulated fines weekly. Screenless design keeps this fast.
Belts and drives: inspect drive belts and the cross-auger belt each season; keep spares.
Burner: service per the burner manual; a Maxon retrofit improves efficiency and reliability.
Drive: maintain the PTO drive or electric motor per configuration; PTO-to-electric conversions are available.
Safety: keep a ULC-approved 2A-10BC fire extinguisher with the dryer; verify the CGA safety shutdown functions.

For burner upgrades, tier kits, controls retrofits, and drive conversions, see the parts and service section of the Vertec hub.

9. Vertec VT6600 FAQ

How much grain can a Vertec VT6600 dry per hour? Used listings quote the VT6600 in the ~600 bu/h class, but this varies significantly with tier count (6/7/9), crop, and moisture removal. The figure is listing-derived, not independently tested — confirm with the seller. For PAMI-tested Vertec numbers, see the VT5600R page.

Is the VT6600 portable? Yes — it’s the portable continuous-flow member of the Vertec range, designed to be moved and sited flexibly, which suits multi-site farms or yards without a fixed tower installation.

What power does the VT6600 need? It commonly runs single-phase, often with a PTO blower, in 4M or 6M BTU configurations — more yard-friendly than the three-phase VT8600. Confirm the specific machine’s drive and fuel with the seller.

How many tiers does a VT6600 have? It appears in 6, 7, and 9-tier configurations on the used market, which is why capacity varies between machines. Always confirm the tier count, as it directly affects throughput.

Is the VT6600 still made? No — it’s a legacy Vertec sold exclusively used in Canada. Parts, burner upgrades, and controls retrofits remain available through prairie specialists.

How much does a used VT6600 cost in Canada? Roughly CAD $12,000–$22,000 for project units, $22,000–$35,000 for good updated machines, and more for higher-tier or fully retrofitted examples. Configuration matters as much as condition.

VT6600 vs VT8600 — which should I buy? The VT6600 is the portable, often single-phase, ~600 bu/h-class machine; the VT8600 is the larger, three-phase, ~1,800 bu/h-class dryer. Choose the VT6600 for portability and single-phase yards, the VT8600 for maximum throughput where three-phase power is available.

10. Related Models on Aglist

Vertec Grain Dryers Compared — full Vertec range, parts, and service hub
Vertec VT5600R — the PAMI-tested mid-size Vertec
Vertec VT8600 — the high-capacity three-phase Vertec
Super-B SQ20 — modern portable continuous dryer alternative
Best Grain Dryers in Canada — full new-dryer buyer’s guide

Disclaimer

Specifications on this page are drawn from Canadian used-market listings and auction records, not independent bench testing; the VT6600 appears in multiple configurations and the ~600 bu/h capacity is a listing quote that varies by tiers, crop, and moisture removal. Pricing reflects used-market listings and varies by condition, configuration, and retrofit status. Reviews on Aglist are written by real users and moderated for spam — opinions are personal. Vertec dryers are decades old and individual machines differ greatly; always confirm specifications, tier count, and power requirements with the seller, a qualified dryer service shop, and the owner’s manual before purchase, service, or repair.